|
F20E-Gfk560/630
Flyer Payoff with glass fibre arm to put in bobbin hole
F21E-Gfk630/710
Flyer Payoff as above but with bigger pulley Ø 40 mm
on the roller head
F23E-Gfk800Y
Flyer Payoff as above but with bigger pulley ¯ 80 mm on the
roller head and with hysteresis brake
|
F21E-Gfk630/710Y |
| |
F20E-Gfk560/630 |
F21E-Gfk630/710 |
F23E-Gfk800Y |
| Flange Ø |
560 - 630 mm |
630 - 710 mm |
800 mm |
| Multiwire |
max. 8 x 0,25 mm |
max. 8 x 0,35 mm |
max. 8 x 0,65 mm |
| Ø Cu-, Al wire |
0,15 - 0,6 mm |
0,20 - 0,8 mm |
0,30 -1,0 mm |
| Ø Steelwire hard |
max. 0,3 mm |
max. 0,4 mm |
max. 0,5 mm |
| Ø Steelwire soft |
max. 0,5 mm |
max. 0,6 mm |
max. 0,7 mm |
| Wire speed |
max.
800m/min |
max.
800m/min |
max.
800m/min |
| Wire tension |
min. 1 N, max. 6 N |
min. 2 N, max. 11 N |
min. 3 N, max. 15 N |
|
Flyer payoff for use of single
wire and multiwire with high speed (max. 800 m/min). Purpose in most
cases is rewinding.
Attention: The unit should be only used with adequate shielding that
the customer should care for. A suitable shielding can be quoted by
mobac on request. |
|
F20G-Gf
560/630HTK
F20G-Gfk 560/630 HTK Flyer Payoff with glass fibre arm, mounted
in frame, with dancer accumulator and wire tension compensator for
spools Ø 560 - 630 mm
F21G-Gfk630/710YHTK
Flyer Payoff as above but with hysteresis brake, for spools
Ø 630 - 710 mm
F23G-Gfk800HTK
Flyer Payoff as above but with pulleys 80 mm on the roller head,
for spools Ø 800 mm
|
| |
F20G-Gfk560/630HTK |
F21G-Gfk630/710YHTK |
F23G-Gfk800HTK |
| Flange Ø |
560 - 630 mm |
630 - 710 mm |
800 mm |
| Multiwire |
max. 8 x 0,25 mm |
max. 8 x 0,35 mm |
max. 8 x 0,65 mm |
| Ø Cu-, Al wire |
0,15 - 0,6 mm |
0,20 - 0,8 mm |
0,30 -1,0 mm |
| Ø Steelwire hard |
max. 0,3 mm |
max. 0,4 mm |
max. 0,5 mm |
| Ø Steelwire soft |
max. 0,5 mm |
max. 0,6 mm |
max. 0,7 mm |
| Wire speed |
max.
800 m/min |
max.
800 m/min |
max.
800 m/min |
| Wire tension |
min. 1 N, max. 6 N |
min. 2 N, max. 11 N |
min. 3 N, max. 15 N |
|
Flyer payoff for use of singlewire
and multiwire with high speed (max. 800 m/min).
Purpose in most cases is rewinding (for example braiding spools). |
|
F21G-Gfk560/800HTK-Y
High Speed Flyer Payoff with following hysteresis brake
For the possibility to increase tension there is a hysteresis brake
following as shown on the picture.
|
| Flange Ø |
560 - 800 mm |
| Multiwire |
max. 8 x 0,35 mm |
| Ø Cu-, Al wire |
0,15 - 0,9 mm |
| Ø Steelwire hard |
max. 0,4 mm |
| Ø Steelwire soft |
max. 0,6 mm |
| Wire speed |
max. 800 m/min |
| Wire tension* |
min. 3 N, max. 25 N |
*depending on rpm |
This kind of Flyer Payoffs
are equipped with glass fibre arms and pulleys made of plastic with
ceramic surface. There are payoff speeds often more than 800 m/min.
in application. |
|
F21G-Gfk560/630HAT
F21G-Gfk630/800HAT
For tension controlled wire speeds up to max. 600 m/min. with
wires for example
6 x 0,1 mm, 7 x 0,13 mm, 7 x 0,2 mm, 12 x 0,19 mm and similar dancer
regulated driven Flyer Payoffs are preferably used.
|
| Flange Ø |
560 - 800 mm |
| Multiwire |
max. 12 x 0,19 mm |
| Ø Cu-, Al wire |
0,1 - 0,9. mm |
| Ø Steelwire hard |
max. 0,3 mm |
| Ø Steelwire soft |
0,08 x 0,19 mm |
| Wire speed |
max. 600 m/min |
| Wire tension* |
min. 1 N |
*unabhängig von Drehzahlen . |
The Payoff is equipped with a glas fibre
flyerarm that is driven by an AC-motor. Control of the motor by a
4 Q control unit and frequency inverter. The unit is especially suitable
for high speed in start/stop use. It is working very even and with
constant tension. |
|